Shipping Included on Orders of $25 or More
The X10 TM751 wireless transceiver module is an integral part of your home control system. The TM751 receives radio frequency commands from X10 RF transmitting controls like the IR543 Hand Held IR/RF Remote or computer based software like the ActiveHome Pro Software with CM15A USB Interface , wireless motion sensors etc. The TM751 then converts the received X10 signal into a powerline command down the household wiring. The TM751 does not respond to X10 signals sent down the house wiring, it only responds to RF X10 signals he use of the TM751 will improve X10 communication by allowing for 2 paths of X10 commandsl: RF and transmission line.
Note: For larger X10 systems, it is recommended that 1 TM751 is used per house-code setting. For example, if you have all your interior lights on House Code A, all your exterior lights on House Code B, and all your wireless cameras on House Code C, you would need 3 TM751 Transceivers.
The X10 TM751 plugs into standard wall outlets and provides a 2 prong receptacle that functions as an appliance module. The appliance module defaults to Unit code "1" and whatever house code you set it to and responds to On/Off commands. The front of the TM751 also features push button switch that controls On and Off of the appliance plugged into it. The antenna on the TM751 rotates 360 degrees and extends to 12" so that maximum range may be achieve with minimal obstruction. The appliance portion of the TM751 is rated for use with 15A resistive loads, 1/3HP motor loads, 500W Incandescent Loads and 400W TV Loads.
X10 TM571 Transceiver Specifications:
• Color: White
• Plugs into any std 120VAC wall outlet
• Receives RF X10 Signals and converts to Power Line Communications
• Improves X10 Communications
• Adjustable 360 Degree Antenna extendable from 4" to 12"
• 2 Prong Bottom Mounted Appliance Module Outlet
• Local On/Off Button for control of Appliance Module Outlet
• 120VAC - 500W 4Amp Max
• Dimensions: 2.25" W x 2.92" H x 1.37" D (Not Including Antenna or Plug)
• 1yr Warranty
X10 does not specify the RF range.
We tested to 50' through several walls using Active Home Pro and the CM15A
and it worked flawlessly. Not tested beyond 50'. The usable range may vary
different X10 transmitters or different environments..
View the X10 Cross Reference List
View the X10 TM751 Back Image
View the X10 TM751 Manual PDF
View our X10 FAQ and Downloads Page
TM751
|
|
Shipping Included on Orders of $25 or More
| X10 Pro XPDF Dimming In-Line Module Incandescent Loads
|
|
The X10 Pro XPDF is an In-Line Dimming module for incandescent loads designed to fit inside a typical lighting fixture or signal gang utility boxes. The XPDF provides Dimming, Unit On/Off and All Lights On/Off capabilities through the use of separate X10 controllers like the IR543, ActiveHome Pro Software, UR74A remote controls etc. The XPDF is ideal for controlling bedroom, living room, family room, and Home Theater light fixtures.
The dimmer switch is scene capable with the use of the ActiveHome Pro software which allows the user to numerically set the level of brightness or using your advanced Home Theater remote by programming the Dim/Brighten IR commands for a tested duration to achieve the desired dim level. This switch does not recall or remember settings
Important: The XPDF module requires a Neutral connection. This is not the same as ground. If you are unsure whether or not. Please consult the wiring diagram in the manual below.
Note: Not for use with motors, receptacles, Fluorescent Lighting or Transformers.
X10 Pro XPDF Dimming In-Line Module Specifications:
• In-Line Use - No Manual Switch
• Incandescent Loads Only
• Dimming, On/Off, All On/Off Capable
• X10 Control Capable
• 120VAC - 300W 2.5Amp Max
• Max Operating Temp - 140 Deg F
• Fits Std. Single Gang Box
• Dimensions: 2.94" L x 2.06" W x 1.3" D
• 1yr Warranty
View the X10 Pro XPDF Manual PDF
View our X10 FAQ and Downloads Page
XPDF
|
|
|
Shipping Included on Orders of $25 or More
| X10 Pro XPFM In-Line Module Incandescent / Inductive / Low-Voltage Loads
|
|
The X10 Pro XPFM is an In-Line module for incandescent, Flusrescent, Inductive and small motor loads designed to fits inside a typical lighting fixture or signal gang utility boxes for the control of lights, appliances, fans etc. The XPFM provides Unit On/Off and All Lights On/Off capabilities through the use of separate X10 controllers like the IR543, ActiveHome Pro Software, UR74A remote controls etc.
Important: The XPFM switch requires a Neutral connection. This is not the same as ground. If you are unsure whether or not. Please consult the wiring diagram in the manual below.
X10 Pro XPFM In-Line Module Specifications:
• In-Line Use - No Manual Switch
• Incandescent, Low Voltage and Inductive Lighting or Small Motor Use
• On/Off, All On/Off Capable
• X10 Control Capable
• 120VAC - 1800W 15Amp Max
• Max Operating Temp - 140 Deg F
• Fits Std. Single Gang Box
• Dimensions: 2.94" L x 2.06" W x 1.3" D
• 1yr Warranty
View the X10 Pro XPFM Manual PDF
View our X10 FAQ and Downloads Page
XPFM
|
|
|
Shipping Included on Orders of $25 or More
| X10 LM465 Wall-Plug Dimming Module Incandescent Loads
|
|
The X10 LM465 and X10 Pro PLM01 are both wall plug Dimming modules for incandescent loads. Simply plug the LM465 into an outlet and then plug a 2 prong light fixture into the bottom of the module to get automated control of your lighting. The LM465 / PLM01 provide Dimming, Unit On/Off and All Lights On/Off capabilities through the use of separate X10 controllers like the IR543, ActiveHome Pro Software, UR74A remote controls etc. The LM465 is ideal for controlling bedroom, living room, family room, and Home Theater light fixtures.
The dimmer switch is scene capable with the use of the ActiveHome Pro software which allows the user to numerically set the level of brightness or using your advanced Home Theater remote by programming the Dim/Brighten IR commands for a tested duration to achieve the desired dim level. This switch does not recall or remember settings
Note: Not for use with appliances, motors, Fluorescent Lighting or Transformers.
X10 LM465 Dimming Wall Plug Module Specifications:
• Wall-Plug Use - No Manual Switch
• Incandescent Loads Only
• Dimming, On/Off, All On/Off Capable
• X10 Control Capable
• 120VAC - 300W 2.5Amp Max
• 2 Prong Outlet - No ground connection
• Dimensions: 2.25" W x 2.91" H x 1.36" D
• 1yr Warranty
Stocked as LM465 but is the same as the X10 Pro PLM01
View the X10 Cross Reference List
View the X10 LM465 Bottom/Back Image
View the X10 LM465 Manual PDF
View our X10 FAQ and Downloads Page
LM465
|
|
|
Shipping Included on Orders of $25 or More
| X10 AM466 Wall-Plug Module Appliances and Lights
|
|
The X10 AM466 and X10 Pro PAM02 are both wall plug modules for virtually any kind of load - fans, air conditioner, lights, coffe pots, TVs, motors etc. Simply plug the AM466 into an outlet and then plug a 2 or 3 prong cord into the bottom of the module to get automated control of your devices. The AM466 / PAM02 provide Unit On/Off and All Lights On/Off capabilities through the use of separate X10 controllers like the IR543, ActiveHome Pro Software, UR74A remote controls etc. The AM466 is ideal for controlling virtually any device requiring a 3 prong grounded outlet and up to 15 Amps of service.
X10 AM466 3 Prong 15Amp Wall Plug Module Specifications:
• Wall-Plug Use - No Manual Switch
• Wide Variety of Loads
• On/Off, All On/Off Capable
• X10 Control Capable
• 120VAC - 1800W - 15Amp Max 1/3hp
• 3 Prong Outlet
• Dimensions: 2.25" W x 2.91" H x 1.36" D
• 1yr Warranty
Stocked as AM466 but is the same as the X10 Pro PAM02
View the X10 Cross Reference List
View the X10 AM466 Bottom/Back Image
View the X10 AM466 Manual PDF
View our X10 FAQ and Downloads Page
AM466
|
|
|
Shipping Included on Orders of $25 or More
| X10 UM506 Wall-Plug Universal Contact Closure Module
|
|
The X10 UM506 and X10 Pro PUM01 are wall plug modules used to control a contact closure. This contact closure device can trigger an event by closing contact and completing a circuit. If you are keen enough you can use this device to press a button on a remote that does not have learnable codes like RF remotes. The contact can also be used to pass 24VDC up to 5 amps to gain control of a low voltage device like a horn for an alarm or sprinkler system. The contact of the UM506 may be used in a momentary or sustained contact closure. The UM506 also features a built-in chime so signal activation that can be turned on or off.
X10 UM506 Contact Closure Module Specifications:
• Wall-Plug Use - With Manual Switch
• Wide Variety of Loads
• Provides Contact Closure
• Momentary or Sustained Contact
• Unit On/Off, All Off Capable
• X10 Control Capable
• Contact Rating - 24VDC - 5Amp Max
• Dimensions: 2.2" W x 3.58" H x 1.75" D
• 1yr Warranty
Stocked as UM506 but is the same as the X10 Pro PUM01
View the X10 Cross Reference List
View the X10 UM506 Manual PDF
View our X10 FAQ and Downloads Page
UM506
|
|
|
Shipping Included on Orders of $25 or More
| X10 LM15A - X10 Pro PSM04 Super socket Lamp Module
|
|
The X10 Socket Rocket LM15A is Lamp Module for allowing X10 control of Incandescent Lamps remotely. Great module for gaining control lights in remote locations. The X10 LM15A Socket Rocket can be used indoors or outdoors to control incandescent lamps up to 150W. Simply screw the LM15A into a light socket and then screw a light bulb into the LM15A.
Unlike conventional X10 Modules the LM15A does not have any code wheels. You set its code up from an X10 controller and it then remembers this code, even after a power outage. Because the LM15A remembers its code, you can set it up in any lamp and then move it to its final location (in an outdoor light fixture, for example). Default code is A1.
X10 LM15A Socket Rocket Lamp Module Specifications:
• Incandescent Lamp Module
• For Up To 150W Standard Light Bulbs
• Screws into Std. Light Bulb Base
• For use Indoors or Outdoors
• Responds to On/Off, All On/All Off Commands
• Dimensions: 2.26" L x 1.315" W
• Extends the bulb app. 1.625" from its normal position
• 1yr Warranty
Stocked as the X10 LM15A but is the same as the X10Pro PSM04
View the X10 Cross Reference List
The LM15A can not be used with a standard wall switch to control it. If you want both standard and X10 control of a light the LM465 Lamp Module, SR227 Wall Outlet or the WS12A,WS13A, WS14A, XPDI3 Wall Switch Modules should be used.
View the X10 LM15A Super Socket Manual PDF
View our X10 FAQ and Downloads Page
LM15A
|
|
|
Shipping Included on Orders of $25 or More
| Somfy Shade Home Automation X10 / RS232 16 Channel RTS Interface
|
|
The Somfy RS232 and X-10 interface is a 16 channel RTS transmitter is a versatile home automation interface device for Somfy’s products that are compatible with RTS RF technology. The 16 Channel RTS Interface can be controlled with X-10 powerline system controls or via RS232 communication from a vast array of controllers. This shade home automation controller is capable of individual or group control.
The operation of this X-10/RS232 interface is very similar to the Telis 4 Remote Control but we now have 16 channels available for programminging. Each Channel can handle 1 or many RTS motors. You can control each RTS channel individually or all 16 channels at the same time (Depends on Controlle used to communicate with the X-10/RS232 Interface). You can have the kitchen on one channel, the living room on another or isolate based on location (east, west etc.) You can control each group separately or together from nearly any location in the house. All shades or motors assigned to 1 specific channel will operate simultaneously. When used with the LT30 motors it controls Up, Down, Stop and customer preferred location commands. RTS technology RF Control devices have a 65’ range through 2 concrete walls and nearly a 100’ clear path range.
Note: The X-10/RS232 to RTS interface can not program the limit points on Somfy RTS motors. You will need a Telis Remote or similar RTS controller to program the shade motors. This interface simply provides the ability to comminucate up/down/and stop commands to 16 rts channels.
The Somfy X10 to RTS Interface is compatible with X10 Controllers, Leviton DHC and a variety of other X10 Compatible Controllers having Birght and Dim commands.
Somfy X-10/RS232 to RTS Interface 1810686 Specifications
· X-10/RS232 to RTS RF Home Automation Interface
· 16 Individual RTS Channels of communication
· Can be controlled with: X-10 Controllers or RS232
· Plugs into std wall outlet
· Power LED communicates power status
· Transmit LED communicates signal status
· 16 Position Rotary switch for channel selection during programming
· Prgram button for assigning motors to channels
· RS232 connector on the side for RS232 communication
· Color: Off-White
· Dimensions: 4.1” H x 2.25” W x 1.55” D
· Somfy part #1810686
Somfy X10/RS232 RTS Interface Side View Image
Somfy X10/RS232 RTS Interface Back View Image
Somfy X10/RS232 RTS Interface Installation Instructions PDF
Roller Shade Components Index Page
Most people want shade automation with IR remotes so we have tested the following controls for compatibility with IR systems. UR74A Universal Remote, IR543 IR receiving Mini Controller, Active Home Pro w/CM15A USB computer interface.
The IR543 Mini Controller allows IR X-10 commands to be received and sent down the housewiring to the Somfy X10 RTS Interface. We tested the IR control with the X10 UR74A which has learnable IR codes and the system worked quite well. You can also control this interface with X10 wired and RF controllers as well. The X10 ActiveHome Pro w/CM15A interface module is a nice addition to the system if you want to us a PC to add scheduled timers to your control system based on time and days. See our X10 Automation Page for info X10 devices.
1810686
|
|
|
Shipping Included on Orders of $25 or More
| X10 SR227 - 120VAC 15 Amp Programmable Outlet
|
|
The X10 SR227 and X10 Pro PA011 are programmable wall outlets rated at 15 amps. The SR227 can be used to control power to any device rated for 15AMPs or less. The top receptacle is controlled by X10 commands and the bottom is always on. The SR227 / PA011 provide a clean unobtrusive look for X10 control.
X10 SR227 Programmable Outlet Specifications:
• Wall Outlet
• Color - White Only
• Unit On/Off, All Off Capable
• X10 Control Capable
• 120VAC - 15Amp
• Fits Std. Utility Box - Depth Required - 1.35"
• Includes White Trim Plate
• 1yr Warranty
Stocked as SR227 but is the same as the X10 Pro PA011
View the X10 Cross Reference List
View the X10 SR227 Back Image
View the X10 SR227 Manual PDF
View our X10 FAQ and Downloads Page
SR227
|
|
|
Shipping Included on Orders of $25 or More
| X10 HD243 - 220VAC 15 Amp Heavy Duty Appliance Programmable Module
|
|
The X10 HD243 can control any 220/240V appliance rated at up to 15a. The HD243 provide On/Off Control. The HD243 plugs into an existing 220/240VAC wall outlet.
NOTE: This module is designed to work on 240V split phase systems only - it will not work on 3-phase (120/208V) wiring unless an X10 PRO XPCR 3-Phase Coupling / Repeater is installed in the main breaker panel at the installation site to correct the sinewave timing.
X10 HD243 Heavy Duty Appliance Module:
• Can control large appliance, heaters, air conditioners, ranges etc.
• 220/240VAC 15Amp Circuit Rating
• UL Listed
• Respons to Unit On/Off, All Off Capable
• X10 Control Capable
• Plugs into Existing - 220/240VAC Outlet
• Dimensions: - 2.25" W x 3.5" D x 2" D (Not Including Prongs)
• 1yr Warranty
View the X10 HD243 Back Image
View the X10 HD243 Manual PDF
View our X10 FAQ and Downloads Page
HD243
|
|
|
|